UBERTI 1P SAA B-WESTERN GRIPS ~ SINGLE ACTION ARMY Cattleman El Patron Evil Roy

Description: Arizona Custom Grips UBERTI SAA 1873 SINGLE ACTION ARMY STYLE REVOLVERS ~ Exclusive ~ MAGNA-TUSK™ B-Western Style Custom Stag Grips ~~~~~oNE-PIECE (nO SCREWHOLE) STYLETHIS AUCTION IS FOR OUR ONE-PIECE (NO SCREWHOLE) STYLE GRIPS. SEE BELOW.********Note: Two-Piece grips, in addition to a visible screw, have a grip pin installed in the grip frame to help hold them in place. One-Piece grips (grips with no visible screw) use a spacer between the panels, with no screw and no grip pin. Our grips will interchange and work on either style of grip frame. See below. One-Piece style grips (i.e., grips which do not have a visible screwhole in the grips) incorporate a user installed spacer between the grip panels, as seen on many of the early Colts. This results in a rock-tight fit, without the need of a screw. Preferred by many collectors for their clean lines and traditional look, One-Piece style grips are removed by removing the three backstrap screws, and pulling the grip and backstrap backwards. Reinstallation is in reverse order. Our One-Piece style grips will work on either style gripframe (either One-Piece or Two-Piece style grip frames). Fully illustrated instructions included for quick and easy installation.Alternatively, our Two-Piece style grips (i.e., grips with a visible screw) offer the superior convenience of quick grip removal. Unlike with One-Piece grips, the backstrap need not be removed to remove the grips for cleaning and maintenance of the revolver. Our Two-Piece grips include a free Conversion kit (allowing their use on One-Piece style frames) which replaces the need for a grip pin and is actually a stronger design, and allows the grips to lock up tight, allowing no movement. This requires no modification to your revolver and gives you the advantage of the ease of maintenance of Two-Piece grips, while preserving the integrity of your revolver in original factory condition. Two-Piece style grips were also used on many of the early Colts, and are a traditional and iconic historical design, offering a distinctive look and convenience preferred by many collectors.Fully illustrated, detailed instructions are included with each set of grips. 04072200 ~~~~~ WHAT THESE WILL and WILL NOT FIT – Please read this section in its entirety to ensure you get the correct grip. A few minutes spent now will avoid unnecessary delay later on. This auction is for a set of Genuine Magna-Tusk™ grips for any of the UBERTI made 1873 SAA (Single Action Army) style revolvers, with the standard sized (around 3-1/6” to 3-1/8” tall) “plowhandle” style grip frames. [Please note that these will NOT fit the taller 1860 Army sized 3-3/8” gripframes – see below].These will be marked “Uberti,” and may also (but not necessarily be) marked by the U.S. importer, such as “Cimarron,” “Taylors & Co.”, “Navy Arms”, “Stoeger”, “EMF”, etc. The important thing to determine is that the revolver was made by Uberti and not by some other maker. If you see your revolver listed below, then these grips WILL FIT (subject to the few exceptions noted below). These grips will fit any of the following Uberti-made revolvers with the standard sized “plowhandle” style gripframe: ● Cimarron Uberti revolvers: Buntline; Cattleman; Cattleman II; Chisholm; Desperado; El Patron; Evil Roy; Frisco; Holy Smoker; Hombre; Horseman; Cimarron Model P and Model P Jr.; New Sheriff; Old West; Pistoleer; Rooster Shooter; Short Stroke CMS Pro; Short Stroke SASS Pro; Stallion; Thunderstorm and Thunderstorm CM; US Military Models (Custer 7th Cavalry, U.S. Cavalry Scout, and U.S.V. Artillery); Wyatt Earp Buntline, and Wyatt Earp Cody; ● Taylor’s & Co. Uberti revolvers: Cattleman (NOTE: these will NOT fit the Cattleman .44 Mag which uses the larger 3-3/8” gripframe – see below); Cattleman 12-Shot; Devil Anse; Drifter; Gambler; Old Randall; Outlaw Legacy; Ranch Hand; Runnin’ Iron; Smoke Wagon; Stallion .22, Taylor Gambler; and Taylor Marshall. (Note: will NOT fit the Taylor’s Gunfighter or Gunfighter Defender, both of which use the larger 3-3/8” gripframe – see below);● Also: Will also fit any of Stoeger’s Uberti revolvers; the E.M.F. Dakota II or Dakota III; the American Arms Regulator; or any other Uberti SAA style revolver with the standard sized (3-1/6” to 3-1/8”) plowhandle grip frame.Note: If you do not see your revolver listed, please drop us an email with your model name and we will verify your revolver. UBERTI FRAME VARIATIONS -- IMPORTANT!*PLEASE NOTE: Over the years Uberti has used multiple variations of gripframes on their SAA style (“Colt” style) revolvers, and they are not interchangeable. Accordingly, please send us an immediate followup email after your purchase (or attach a note to your order) informing us of the two-digit code found in the small rectangular box stamped underneath or on the side of the receiver (or occasionally found under the barrel). This is shown in the second photo as an example. This can be either letters or numbers. Also, please send us the first three digits of your serial number. If there is a letter before before your serial number (some will have it and some won’t), please also include that. This will tell us the gripframe variation you have, and we will need this information to make sure you get the correct grips. If we do not receive this information from you, we will send out the most common variation for the latest models. What these WILL NOT FIT: 1. Please note that these grips will NOT fit other makes of revolvers, such as revolvers made by Pietta, Armi San Marco, Colt, Ruger, etc. Also, please note that these grips are made to fit the standard “Plowhandle” shaped (“SAA style”) gripframes only; these grips will NOT fit completely differently shaped gripframes, such as the Bisley, the Birdshead, the Thunderer or the Lightning style gripframes. Please check your revolver to make sure you do not have one of these, or send us a photo of your gripframe if you are unsure. We make grips for all of these different styles which you can find in our store, so please email if you have any questions or cannot find what you need. A photo would of your gripframe or grips be helpful.2. ALSO PLEASE NOTE, as a reminder, these grips are made for STANDARD SIZED grip frames ONLY and WILL NOT FIT any larger (taller) 1860 Army sized grip frames. Please check your grip frame measurement prior to ordering. Your grips or grip frame should measure somewhere between 3-1/16 – 3-1/8” tall, depending on how you hold your ruler, tape, or caliper. Some revolvers use a taller 3-3/8” 1860 Army sized grip. Taylor & Co.’s Gunfighter or Gunfighter Defender, Taylor’s Cattleman 44 Mag., Cimarron’s Bad Boy, the El Patron Grizzly Paw, and the Uberti Callahan, for example, have a taller 3-3/8” grip frame. If you have one of these, our Uberti 1860 Army “Conversion & Metallic Cartridge” grips will fit these revolvers. Please see our store and search under the proper category or email us if you cannot find what you need. IN SUMMARY: 1) Make sure you have the standard “plowhandle” shaped 3-1/8” gripframe and not the taller 3-3/8” frame, and that your revolver was made by UBERTI; and 2) please send us the two-digit code found on your revolver (as shown in the second photo), and the first three digits of your serial number, including the prefixed letter if there is one.Please contact us if you cannot find what you need, or if you have any questions. We are always happy to help.04072200A note on the Italian-produced Revolvers: The Italian firms, located in Northern Italy, have been making SAA style revolvers now for well over a half century, and have made a huge number of makes and models and grip frame profiles with varying configurations over the years. We have an in-depth knowledge of the differing grip configurations, have a large library of gripframe variations from the various makers both old and new, and have vast experience making grips for Uberti, Pietta, Armi San Marco, and the other Italian gunmaking firms. Our experienced makers go to great lengths to ensure an exacting fit, including utilizing modern precision CNC production techniques, as well as incorporating old-time hand tuning and hand checking the fit of every grip on our reference frames prior to leaving our factory. We have a long list of many satisfied customers in the shooting industry who have purchased grips to use in a wide variety of applications, and we can safely and confidently guarantee proper fit and finish to your complete satisfaction.For an additional charge, custom fitting is an option. Please contact us for further details if you are interested in custom fitting. 10232100 Arizona Custom Grips Handcrafted on an individual Custom basis out of Magna-Tusk™, our solid, dense proprietary substrate which is formulated out of natural materials for an authentic look and feel, and which yields a finished product which is the ultimate rendition of the classic stag grips of the golden era of Westerns. Better materials and our proprietary pigmenting process yields a finished product better than the originals. These grips are milled from a solid slab and are not cast. This avoids the inclusions, air pockets, and most importantly the cheap "cast plastic" look found in the urethane and other imitation materials commonly available. Like natural grips, with use and handling over time they will form an authentic patina and will only improve with age. They look better, age better, and perform better. And perhaps best of all, these grips are made entirely in the U.S.A.! Gun prop and holster not included -- only the grips are for sale. Please note that the grips shown are a stock photo used for illustration purposes only. Your grips will be individually hand cut and appear similar to these. The "B-Western": These "B-Western" Style Custom grips are hand-carved one-at-a-time in recognition of one of America's most outstanding and lasting cultural achievements of the 20th century -- the "B-Western." Styled after the grips seen on the revolvers of classic Hollywood Westerns of the 1930's to the 1960's (the "golden era of Hollywood Westerns"), these grips were featured in numerous Western productions both on Television and on the Silver Screen. Gunsmoke, Bonanza, The Rifleman, Rawhide, The Virginian, and many others too numerous to mention, all took America back to a simpler time and place. Times have changed, but the lessons and values of that unforgettable period still have a place in the hearts of millions of Americans and many other Western fans throughout the world who appreciate the enduring contribution to our culture and society made by the unique and colorful characters of the Old West. 4.18.13 Arizona Custom Stag™ Grips: These grips are completely unique, custom, and one-of-a-kind. Each is hand cut, and no two are the same. You will not find another set like them on any gun at any Western event, guaranteed! Hand made in painstaking, exacting detail to authentic feel and dimensions. We strive for museum quality with every pair. Arizona Custom Stag™ looks, feels, and ages like the genuine product, with durability far exceeding Ivory (Ivory is a relatively fragile material, which often cracks under stress and age). Magna-Tusk™, our Premier Grade product used in these grips, is filled with natural materials, and works and polishes as well as looks like the real thing. It takes carving with superior detail and definition, and accurately captures that authentic, weathered, deep, dark chocolate brown/black color in the bark pattern sought after by stag collectors. With age, it develops a soft, mellow patina which makes it indistinguishable from the more expensive and fragile product. These grips are used in professional applications where only the best will do. We have supplied these grips to Hollywood and other locations that demand only the best in durability, design, and authenticity. We cut no corners, and make every grip with the intention of it being a grip which will last a lifetime. A fine revolver deserves a fine grip. If you have been looking for the ultimate B-Western grip, you won't be disappointed!! The durability and excellent aging characteristics of these grips are enhanced by our exclusive and permanent bonded pigment application process which, once cured, won't chip, crack, or peel like superficially applied paint products found on less expensive grips. Accept no substitutes. Arizona Custom Stag™ adds a touch of class and realism which is completely lost by using lesser quality "cast plastic" imitations available elsewhere. Grip screws included with all grips. As with all Single Action grips, minor fitting may be, but is not usually, required due to small variations in grip frames. Full instructions included with all grips. The distinctive qualities and authentic presentation of Arizona Custom Stag™ offers an authentic look, heft and feel which invoke the aura and spirit of the Old West. Guaranteed to please even the most discriminating collector and Western memorabilia aficionado. Full money back, less shipping, if not fully satisfied! If returning, please note that the product must be returned in original, unaltered condition. Remember, above all: Ride Hard, Shoot Straight, and Speak the Truth! Happy Trails!!

Price: 144.95 USD

Location: Mesa, Arizona

End Time: 2024-03-07T21:55:31.000Z

Shipping Cost: 5.99 USD